• Yoke Test Weight

    0 out of 5

    The Yoke Test Weight is a certified 10 lb weight designed specifically for AC magnetic yokes to confirm the yoke has sufficient strength to perform magnetic particle inspections. Each Yoke Test Weight has a built-in leg positioning guide to assure balanced distribution and accurate test results.

    $140.00
  • Yoke Light

    0 out of 5

    The Yoke Light is an add-on accessory for Y-1 and Y-7 AC yokes which provides focused, visible light to the yoke inspection area when the yoke is activated. The 10 lumens strong light is designed to enhance visible detection of flaws and discontinuities under low conditions and in difficult to reach areas not accessible to a secondary light source.

    $45.00
  • YM-5

    0 out of 5

    The YM-5 is a portable permanent magnetic yoke designed with hinged arms and rotating pole pieces to allow a wide variety of test part profiles to be magnetized, while the specially shaped pole pieces permit easy removal from the component for cleaning.

    $765.00
  • Y-8 MV Kit

    0 out of 5

    The Y-8 is a battery-powered, DC electromagnetic yoke designed to stand up to the most rugged applications. True portability for magnetic particle inspection in the field and remote locations is achieved through a compact battery pack which provides a full 8-hour shift of inspection power.

    $1,220.00
  • Y-7 MV Kit

    0 out of 5

    The Y-7 MV Kit comes with a durable, high-strength electromagnetic AC/DC yoke and non-fluorescent magnetic powers finds surface and sub-surface indications during mag particle testing.

    $910.00
  • Y-7

    0 out of 5

    The Y-7 is a durable, high-strength AC/DC magnetic yoke designed to detect surface and sub-surface indications in the most rugged applications.

    $860.00
  • Y-2 MV Kit

    0 out of 5

    This 115V Yoke Kit includes gray and red magnetic powders, yellow paint marker, and a cleaning cloth

    $770.00
  • Y-2

    0 out of 5

    The Y-2 is an AC electromagnetic yoke, ergonomically designed to improve productivity and reduce operator arm and wrist fatigue. The yoke generates a strong AC magnetic field for the detection of surface indications during magnetic particle testing.

    Lightweight with an ergonomic grip and trigger, the Y-2 is designed for the rugged demands of field inspection. Featuring a field swappable cord and isolated trigger switch; the Y-2 is easily serviceable because a severed cord should not stop a job from getting done.

    $700.00
  • Y-1 MV Kit

    0 out of 5

    The Y-1 MV Kit includes an ergonomic, light-weight electromagnetic AC yoke and visible magnetic powers for finding surface indications during magnetic particle testing.

    $740.00
  • Split Coil

    0 out of 5

    These handy portable magnetic coils are great for field applications to magnetize a variety of part sizes and shapes for magnetic particle inspection. Use with any Magnaflux electromagnetic current generators for quick, easy part processing.

    $5,510.00
  • S-66

    0 out of 5

    Magnaflux demagnetization units remove any residual magnetism remaining after conducting Magnetic Particle Inspection.  Demagnetization of ferromagnetic parts and materials often requires a requisite to final finishing or to ready an item for its ultimate use.

    $3,600.00
  • S-1212

    0 out of 5

    Magnaflux demagnetization units remove any residual magnetism remaining after conducting Magnetic Particle Inspection.  Demagnetization of ferromagnetic parts and materials often requires a requisite to final finishing or to ready an item for its ultimate use.

    $9,600.00
  • P-70

    0 out of 5

    P-Series portable power packs are convenient and economical inspection units that are used in a wide range of magnetic particle inspection applications that require only moderate power.

    $5,400.00
  • P-1500

    0 out of 5

    P-Series portable power packs are convenient and economical inspection units that are used in a wide range of magnetic particle inspection applications that require only moderate power.

    $6,600.00
  • Mag Kit

    0 out of 5

    Mag Kit, 39 in / 99 cm head opening, 11 in / 28 cm coil (power pack and 4/0 cables sold separately)

    $6,000.00
  • L-10 Coil

    0 out of 5

    These handy portable magnetic coils are great for field applications to magnetize a variety of part sizes and shapes for magnetic particle inspection. Use with any Magnaflux electromagnetic current generators for quick, easy part processing.

    $1,215.00
  • Hood Assembly for Mag Kit

    0 out of 5

    Our durable equipment hood or curtains are used to darken the inspection area to levels well below the common standards and create a very functional inspection environment while keeping operator comfort and convenience in mind.

    $3,000.00
  • Flat Magnetic Coil

    0 out of 5

    These handy portable magnetic coils are great for field applications to magnetize a variety of part sizes and shapes for magnetic particle inspection. Use with any Magnaflux electromagnetic current generators for quick, easy part processing.

    $6,425.00
  • Fixed Coil

    0 out of 5

    Ensure your magnetic inspection bench fits every part you test with this line of fixed magnetizing coils by outfitting your wet bench to match your range of parts, and optimize magnetic field application. Whether you are testing a large pieces or small bolts, these heavy-duty magnetic coils will help you set-up your Magnaflux machine just the way you need.

    $2,585.00
  • Clam Shell Coil

    0 out of 5

    Ensure your magnetic inspection bench fits every part you test with this line of fixed magnetizing coils by outfitting your wet bench to match your range of parts, and optimize magnetic field application. Whether you are testing a large pieces or small bolts, these heavy-duty magnetic coils will help you set-up your Magnaflux machine just the way you need.

    $11,500.00