• Tool Steel Ring

    0 out of 5

    The Tool Steel Ring / Ketos Ring is a mag particle test piece with pre-drilled holes to simulate subsurface discontinuities. It offers a reliable method of verifying magnetic particle system performance when actual test parts with discontinuities are not available.

    $620.00
  • Steady Rest

    0 out of 5

    Steady Rests are used to support and stabilize long or heavy parts such as crankshafts during the inspection process.

    $720.00
  • Standard Prod Set

    0 out of 5

    These handheld electrodes and contact clamps are convenient for conducting sectional magnetic particle inspections, like welds, castings or forgings, or testing parts that cannot be inspected on a wet horizontal bench, such as large fabrications, tubing, bars and tubular assemblies like aircraft mounts and fuselage sections.

    $615.00
  • ST700

    0 out of 5

    The ST700 is an inspection-grade overhead LED UV flood lamp with high-intensity UV-A illumination for non-destructive testing examinations such as fluorescent penetrant and magnetic particle testing.

    $5,500.00
  • Small Parts Adapter

    0 out of 5

    Magnaflux adapters permit the use of standard wet horizontal test units for inspection of small parts such as bolts, screws, pins, etc. Mounted directly to either the head (PN 28470) or tail stock (PN 28471) the solid copper adaptors maintain adequate clearance to proper clamping action.

    $275.00
  • Shunt, 1000A

    0 out of 5

    Shunt, 1000A

    $420.00
  • Replacement copper braid for contact clamp, 1 x 11 in / 2.5 x 30 cm

    0 out of 5

    Replacement copper braid for contact clamp, 1 x 11 in / 2.5 x 30 cm

    $50.00
  • Remote control cable for P-Series, 15 ft

    0 out of 5

    Remote control cable for P-Series, 15 ft / 4.6 m

    $435.00
  • Rail-mounted steady rest, 3 in riser

    0 out of 5

    Rail-mounted steady rest, 3 in /7.6 cm riser

    $1,393.00
  • QQI

    0 out of 5

    Quantitative Quality Indicators (QQI) are magnetic particle test piece shims with artificial defects used to verify field direction and relative strength. QQI’s are also used to balance multi-directional fields and to increase productivity by minimizing magnetizing shots.  The QQI indicator shims are packaged in sets of five.

    $250.00
  • QB-2

    0 out of 5

    The QB-2 is a microprocessor-controlled shot timer and quick break tester which provide quantitative verification of magnetic particle equipment performance by confirming quick break function and measuring magnetizing shot duration, for better magnetic particle inspection quality.

    $1,780.00
  • QB-1

    0 out of 5

    The QB1 is a Go/No-Go gage to demonstrate the quick break function of 3-phase full-wave DC magnetic particle equipment is functional for superior magnetic particle inspection quality.

    $495.00
  • Portable Spray System

    0 out of 5

    30 gal portable Magnetic Particle Spray System with 15 ft recirculation hose and fan pattern spray gun for inspecting large parts during wet method magnetic particle inspection.

    $9,380.00
  • Pie Field Gauge

    0 out of 5

    The magnetic particle Pie Gauge is used as an aid in determining the direction of magnetic fields for detection of discontinuities in ferrous metals.

    $310.00
  • MD-Series Magnetic Bench

    0 out of 5

    The MD-Series multi-directional magnetic bench offers Alternating Current, Half Wave Direct Current and 1-phase Full Wave Direct Current for time-saving multidirectional magnetization which can find defects in all orientations with one mag-cycle.

  • Magnetic Particle Test Bar

    0 out of 5

    Test bar contains coarse and fine surface and subsurface defects in both directions. Meets or exceeds most industrial and military standards for artificial test specimens.

    $630.00
  • Magnetic Flux Indicator Strips

    0 out of 5

    Flexible indicators used to detect appropriate levels of magnetic field strength and directional orientation during the magnetic particle testing process. Each indicator contains three milled slots with widths of .0075″, .009″ and .010″ that share  a common depth.

    $175.00
  • Lead Contact Plate

    0 out of 5

    Magnaflux lead contact plates prevent arc burn by helping maintain proper electrical contact between test parts and contact heads.

    $72.00
  • Heavy-duty braided lead pad, mag kit

    0 out of 5

    Heavy-duty braided lead pad, mag kit

    $406.00
  • Heavy-duty “C” Contact Clamp

    0 out of 5

    Heavy-Duty Contact Clamp is used for parts up to 7” diameter.

    $1,000.00
  • FSM-2

    0 out of 5

    The FSM-2 is used for tangential measuring of the magnetic field strength in DC and AC fields. A tangential field probe is attached to the workpiece’s surface during magnetisation, and the hall sensor measures the voltage change produced by the magnetic field. This meter measures the true RMS of asymmetric magnetic fields.

    $2,500.00
  • EV6500

    0 out of 5
    $1,880.00
  • EV6000 ZP Kit

    0 out of 5
    $2,080.00
  • EV6000 MG Kit

    0 out of 5
    $2,080.00
  • EV6000

    0 out of 5
    $1,880.00
  • Digital Hall Effect Meter

    0 out of 5

    The Digital Hall Effect Meter portable gauss-meter measures the strength of AC alternating-current and DC direct-current magnetic fields. The hand-held digital guassmeter features an easy-to-read LCD screen and simple push button operation.

    $3,070.00
  • Digital Ammeter & Shunt

    0 out of 5

    The Digital Ammeter & Shunt is used to verify magnetizing current output of magnetic particle inspection equipment up to 10,000 amps on half-wave DC, 1-phase full-wave DC and 3-phase full-wave DC output, and up to 6,000 amps on AC current output.[GE1]

    $2,510.00
  • D-Series Magnetic Bench

    0 out of 5

    The D-Series is one of our most powerful wet magnetic benches. Providing 3-phase Full Wave Direct Current, this MPI equipment offers maximum magnetization for finding surface and sub-surface defects with clearer indications while using minimal power.

  • Copper Contact Pad

    0 out of 5

    Magnaflux copper braided contact pads prevent arc burn by helping maintain proper electrical contact between test parts and contact heads.

    $56.00
  • Contact Block

    0 out of 5

    Permits remote testing of parts that are too heavy or too large for processing on unit.  When clamped between head and tailstock, the block supplies magnetizing current to remote prods or clamps through flexible cable (cable not included, see cables and connectors).

    $140.00
  • Centrifuge Tube

    0 out of 5

    Centrifuge tube for 14A particles (use with 14A, 14AM, and 20B)

    $190.00
  • AD-Series Magnetic Bench

    0 out of 5

    The AD-Series magnetic benches provide 4,000 amps of Alternating Current and 5,000 amps of Direct Current magnetization for finding surface and sub-surface defects during wet method magnetic particle inspection.

  • A-Series Magnetic Bench

    0 out of 5

    The A-Series magnetic benches provide Alternating Current magnetization for finding surface defects during wet method magnetic particle inspection.

  • 4/0 Lug

    0 out of 5

    4/0 lug for permanent attachment to magnetizing equipment.

    $22.00
  • 10 Gauss Field Meter, Un-Calibrated

    0 out of 5

    Rugged, pocket-size meters used to indicate residual magnetism remaining in part after magnetization. Inexpensive, disposable, non certified field indicator.

    $43.00